| Brand | GM Genuine Parts |
| Abutment Clips Included | No |
| Anti-Rattle Spring Included | No |
| Bleeder Screw Included | Yes |
| Bleeder Screw Quantity | 1 |
| Bleeder Screw Thread Size | M10 |
| Bleeder Thread Diameter | M10x1.5 |
| Caliper Color | Silver |
| Caliper Slides Included | No |
| Caliper Type | Floating |
| Casting Material | Cast Iron |
| Casting Number 1 | L |
| Casting Number 2 | WF |
| Casting Number 3 | 0000 |
| Casting Number 4 | R |
| Casting Number 5 | 0 |
| Disc Brake Caliper Casting Material | Cast Iron |
| Features & Benefits - Bullet 1 | Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE) |
| Features & Benefits - Bullet 2 | GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors |
| Features & Benefits - Bullet 3 | GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle |
| Features & Benefits - Bullet 4 | GM regularly updates production and service part designs to integrate new materials and technologies |
| Good Maintenance Practices - Section 1 - Bullet 1 | Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations. |
| Good Maintenance Practices - Section 1 - Bullet 2 | Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required. |
| Good Maintenance Practices - Section 1 - Bullet 3 | Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary). |
| Good Maintenance Practices - Section 1 - Bullet 4 | Check the thickness of your brake pads. |
| Good Maintenance Practices - Section 1 - Header | The following inspections and maintenance procedures can help prevent potential brake problems. |
| Good Maintenance Practices - Section 2 - Bullet 1 | Inspection of the brake hoses for brittleness or cracking. |
| Good Maintenance Practices - Section 2 - Bullet 2 | Inspection of brake lining and pads for wear or contamination by brake fluid or grease. |
| Good Maintenance Practices - Section 2 - Bullet 3 | Inspection of wheel bearings and grease seals. |
| Good Maintenance Practices - Section 2 - Bullet 4 | Parking brake adjustments (as needed). |
| Good Maintenance Practices - Section 2 - Header | The following should be conducted by a qualified technician: |
| Grade Type | Regular |
| Height (in) | 1.3 |
| Inlet Fitting Type | Straight |
| Length (in) | 5.1 |
| Mounting Bolt Included | No |
| Mounting Bracket Included | No |
| Mounting Hardware Included | No |
| Mounting Hole Diameter | 0.4 |
| PADB ID 2223 | 0.39 |
| Pad Wear Sensor Included | No |
| Pads Included | No |
| Piston 1 Diameter (in) | 1.99 |
| Piston 2 Diameter (in) | 1.99 |
| Piston Material | Phenolic |
| Piston Quantity | 2 |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 1 | Vehicle pulls to the left or right when brakes are applied. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 2 | Brake pedal pulsation (not to be confused with normal ABS operation). |
| Weight (lb) | 0.22 |
| Width (in) | 2.4 |
